Centreboard 40' - Standard inventory (interior version C)
Download Standard delivery specification PDFCONSTRUCTION
- Casco constructed of CNC cut shipbuilding steel quality ST42. CO2 welding with ESAB wire.
- Hull is stiffened every 400 mm with 8 mm steel frames. Additional webframe just before the mast, reinforced backings for chainplates.
- Stem made of stainless steel shaft, 30mm diameter.
- Through hull fittings, stand-pipes and gunwale (oval) of firm steam pipe.
- Mast support made of 2 ˝" firm steam pipe with transit of mast cables.
- Anchor foundation made of stainless steel, sandblasted and painted.
- Drainage gangways through stainless steel wells at lowest point.
- Stainless steel chainplates welded on casco.
- Stainless steel strip for mounting organizers, jib track, traveller etc. welded on casco, no bolts through the deck.
- Stainless steel pins for stanchions protruding through the deck and welded to the frames.
- Scupperholes, edges near bollards, winches and other wear areas finished with stainless steel.
- Bottom plate, keel with keel sole and centreboard box made of 12mm thick shipbuilding steel.
- Stainless steel bolts welded to hull for mounting two zinc anodes.
- Profiled non ballasted centreboard, very solid construction.
- Centreboard and centreboard box fully hot-dip galvanized (60 kg zinc) which provides for lifetime preservation.
- Centreboard axe 90mm diameter in high quality synthetic bearings. Equipped with lever for hydraulic cylinder.
- Three ballast blocks lead: 2 x 1400kg placed in watertight compartments around centreboard box and 1 x 550kg in box keel underneath the engine. Enclosed with resin and welded on steel top plates.
- PUR insulation hull till below the waterline. Cabin insulation with cork sheets.
- Plastic tanks for fresh water, fuel (day tank and main tank) and black water. Certified.
- Self-draining centre cockpit and cockpit seats with hot-dip galvanized drainpipes.
- Integrated gas storage in aft deck.
- Large integrated storage locker (800 liter) in aft deck with two aluminium hatches and gassprings.
- Drainage around storage lockers and gas storage made of stainless steel U-profiles.
- High quality Awlgrip paint system based Akzo Nobel.
DECK, COCKPIT AND SUPERSTRUCTURE
- Solid synthetic rub rail with stainless steel end plates.
- Portholes (10 rectangular, round 2) and deck hatches (3), make Gebo.
- Fixed 5-piece windshield, make GEBO.
- Sprayhood on stainless steel frame.
- Washboards in PVC.
- Sliding hatch companionway in aluminium, sliding in flush garage.
- Sheltered centre cockpit with ergonomic composite seats.
- Water and fuel deck fillings, outlet for holding tanks.
- Two jib tracks on gunwale, two cuttersail tracks on cabin roof.
- Mainsheet traveller on aft cabin roof.
- Two Lewmar ST50 selftailing winches.
- Three Lewmar ST40 selftailing winches.
- Two Lewmar organizers with four pulleys.
- Two Lewmar turning blocks for cuttersail sheets.
- Two Lewmar turning blocks for jib sheets.
- Four sturdy stainless steel bollards fore and aft.
- Four stainless steel cleats amidships.
- Two stainless steel handrails on cabin roof.
- Double stainless steel lifelines, step through amidships. Height above deck 70 cm, stainless steel stanchions 30 mm diameter.
- Pushpit stainless steel. Pulpit stainless steel.
- Bathing ladder stainless steel, integrated in pulpit.
- Radar mast stainless steel integrated in pulpit.
- Electric windlass with chain stopper.
- Delta anchor 16 kg with 50 meter galvanized 8 mm chain.
- Self-draining plastic chain locker.
- Roller for anchor passage in short stainless steel bowsprit plus transit for additional anchor or mooring line.
- No slip deck paint.
- Ufo type vent, two dorado type vents, ventilation through upper washboard.
RIGGING AND SAILS
- Cutter rigged with mainsail, jib and cuttersail. Total upwind sail area 85.6 m2.
- Deck stepped mast with double spreaders and boom in anodised aluminium alloy, make Seldén.
- Oversized mast section. Running backstays not necessary, but prepared in mast and hull.
- Mast base make Seldén with integrated blocks.
- Boom vang make Seldén (rodkicker).
- Jib furling system Furlex 300D.
- Mainsail halyard.
- Jib halyard.
- Cuttersail halyard.
- Boom topping lift.
- Mainsail sheet.
- Outhaul for mainsail and three mainsail reefing lines.
- Two jib sheets.
- Two cuttersail sheets.
- Lazy jacks.
- Cover for mainsail.
- Full batten mainsail with cars, 3 reefs.
- Jib designed for furling system.
- Cuttersail.
- Three sail bags.
- Standing rigging 1x19 stainless steel wire and chrome bronze rigging screws.
- Including baby stay.
- Windex.
INTERIOR
- Designed for comfort in harbour as well as sailing.
- Interior woodwork in teak, either solid or veneer on marine ply.
- Satin varnished.
- Ceilings finished in bright colours.
- Soles with synthetic teak veneer with bright lines.
- Ceilings and soles are removable where necessary.
- High quality mattresses and cushions with removable high quality fabric covers.
- Matching curtains in saloon.
- Deck hatches with (mosquito) screens.
AFT OWNERS CABIN
- Double berth with mattress and storage space under berth.
- Yachtiflex slats under mattress.
- Two bed side lockers.
- Hanging locker starboard side, locker portside.
- Door portside gives access to workbench/head, door starboard side gives access to galley.
- Inspection hatch to engine compartment.
- Two reading lights.
- Two ceiling lights.
- 230V double socket.
HEAD / WORKBENCH
- Access to head/workbench from aft cabin and saloon.
- Work bench (70 cm) on side of the aft cabin with storage space on the inside of the hull.
- Head with toilet and shower, water resistant finish.
- Shower curtain between toilet and shower.
- Marine toilet with electric pump, connected to holding tank.
- Toilet paper holder and soap dish.
- Corian counter top with wash basin.
- Tap/shower with pressurised hot/cold water.
- Mirror.
- Seat in front of the engine compartment.
- Inspection hatch to engine compartment behind seat.
- Two ceiling lights.
GALLEY
- Seaworthy galley.
- Corian counter top with sink.
- Tap with pressurised hot/cold water.
- Stainless steel oven and grill with three burners stove on gimbals.
- Gas shut-off valve.
- Lots of storage space.
- Seat in front of the engine compartment.
- Inspection hatch to engine compartment behind seat.
- Fridge 80 liter under seat.
- Two lights above sink.
- Two 230V double sockets.
SALOON AND NAVIGATION TABLE
- L-shaped sofa on portside, can also be used as a sea berth.
- Storage space under L-shaped sofa.
- Lockers and book shelf on portside.
- Saloon table with storage for bottles.
- Sliding door gives access to forward cabin.
- Navigation table with seats on both sides.
- Storage space under navigation table seats.
- Storage space in main bulkhead behind navigation table seat.
- Storage space in navigation table.
- General electric panel next to navigation table.
- Mounting space for equipment next to navigation table.
- Book shelf next to navigation table.
- Locker on portside.
- Door portside gives access to head/workbench.
- Wet locker on starboard side.
- Inspection hatch to engine compartment.
- Four ceiling lights.
- Reading light behind L-shaped sofa.
- Adjustable reading light with night function at navigation table.
- 12V socket at navigation table.
- 230V double socket.
FORWARD CABIN
- Two separate berths with mattresses. Portside berth above the starboard side berth.
- Yachtiflex slats under the mattress.
- Storage space under berths.
- Locker on portside.
- Locker (low) on starboard side.
- Lockers overhead the starboard side berth.
- Inspection hatch to anchor locker.
- Two reading lights.
- Two ceiling lights.
- 230V double socket.
TECHNICAL INSTALLATION
- Plastic water pipes.
- Electric water pump with water filter and large pressure vessel.
- Boiler 40 liter supply 230V and via heat exchanger.
- Electric shower discharge pump.
- Electric pump for holding tanks.
- Two automatic/manually operated electric bilge pumps.
- Manual bilge pump in cockpit with strainer.
- Toilet with PVC piping and odour proof tubes.
- Professional odour filter for holding tanks.
- Electric/hydraulic operated centreboard with a separate battery.
- High quality hydraulic cylinder for lifting the centreboard, including a third pipe with pressure valve.
- Touching the ground the centreboard comes up while the oil flows into the reservoir.
- Proximity switch on cylinder to show up of down position of the centreboard.
- Centreboard is operated at the pedestal.
- Webasto AT5000 Eco heater with five outlets. Thermostatically controlled.
ELECTRICAL INSTALLATION
- All wires are numbered at both ends and at the terminals.
- Electra drawings in a separate book of Swanneblom Elektrotechniek.
- All wires in the PUR insulation through electricity tubes.
- Shore connector stainless steel 16 amp make Ratio with 15 meter cable make Ratio.
- RCD.
- Battery charger 12V/30 amps.
- Battery engine AGM 50Ah.
- Battery centreboard/anchor winch AGM 50Ah.
- Two service batteries AGM 75Ah.
- Batteries with main fuses.
- Emergency switch to start the engine with the service batteries.
- Main switch battery engine 5000A.
- Main switch service batteries 5000A.
- Philippi control panel 230V/12V with 26 switches.
- Volt/Ampere gauges and battery condition monitor (shunt).
- Automatic fuses for 12V and 230V
- Interior lights halogen with wall switches.
- Navigation lights: red/green navigation lights, stern light, top light, deck light, three color masthead.
EQUIPMENT
- Compass on pedestal.
- Raymarine ST60 Tri-data (depth, log, water temperature).
- Electric air horn, low tone.
- VDO gauges freshwater, fuel, holding tanks.
STEERING
- Wheel 800 mm with leather cover, steering pedestal make JEFA.
- Pedestal cover.
- Professional hydraulic steering pump and cylinder.
- Rudder bearings make JEFA, needle bearings.
- Rudder in epoxy composite.
- Emergency steering with a stainless steel emergency tiller.
- Windvane installation prepared.
ENGINE INSTALLATION
- VW-Marine SDI 50/4 diesel 37kW/50hp, low fuel consumption.
- Intercooling.
- Electric pump for oil change.
- Air intake filter lifelong guaranteed, washable.
- Alternator 12V-90amps.
- Tachometer and hour meter at pedestal.
- Electronic fuel consumption monitor at pedestal.
- Acoustic and visual alarms for engine temperature, oil pressure and charging at pedestal.
- Gearbox Hurth ZF25.
- Homokinetic joint Aquadrive including thrust bearing.
- GRP propeller shaft stern tubes.
- Volvo seal on stern tube.
- Fixed 3-bladed propeller.
- Electric fuel pump between main fuel tank and day fuel tank.
- Fuel filter in metal with water alarm.
- Fuel filling on deck with overflow protection.
- Fuel tanks with odour filter in air vents.
- Protection against fuel bacteria.
- Mechanical ventilation in engine compartment.
- Engine compartment carefully soundproofed.
- Motor accessible from all sides.
- Automatic fire extinguisher in engine compartment.
- Light in engine compartment.
EQUIPMENT
- Two fire extinguishers 2 kg.
- Fire blanket.
- Four 15 meter long braided polyester mooring warps 16 mm.
- Six fenders including lines.
- Two winch handles.
- Bucket.
- Hook.
- Flag pole with national flag.
- ACCES database program with all the part numbers and links to suppliers.
- DVD with extensive photo report of the building.
- Extensive owners manual.
GENERAL SPECIFICATIONS
- Length overall: 12.93 m
- Length on deck: 12.00 m
- Length waterline: 11.00 m
- Beam overall: 3.92 m
- Beam hull: 3.80 m
- Draft min/max: 1.20 m/2.50 m
- Height above waterline: 17.80 m
- Displacement: 13,500 kg
- Ballast: 4050 kg (3350 kg lead, bottom plate 700 kg)
- Water: 250 liter
- Fuel main tank: 210 liter
- Fuel day tank: 55 liter
- Holding tanks: 210 liter
- Mainsail: 38.3 m2
- Cuttersail: 17.3 m2
- Jib: 40.0 m2
- CE certificate: A, ocean.
- Design: Dick Koopmans.
Measurement and weights are given to you in best knowledge. Construction and detail modifications may be made without prior notice.